If you’re attempting to screw things into concrete, just about the worst thing imaginable is having your drill bounce back and forth on you while trying to use a masonry bit.
One way that some people attempt to get around this problem is by using a “hammer” setting on their drills. However, doing so can actually crack your concrete!
Is drilling into concrete possible without a hammer drill?
The Hammer Drill was created to be the tool required for drilling on a concrete surface. Because the concrete and the hammer drilling hardness make it simpler to drive masonry drill bits without requiring many drill bits or forcing the motor to overheat.
When you need to create drills into concrete on a regular basis, it’s preferable to hire or buy hammer drills. Remember that it should only be utilized as a last resort. You can get the same results with a regular drill if you know how to do the right thing with a correct drill. Some nails might also be used.
Steps on How to Screw Into Concrete Without a Hammer Drill
Step 1: Have the Right Drill Bits
You can not just pick any drill bit and start drilling through concrete. You need a special bit designed for concrete.
While there are several drill bits made specifically for concrete, one of the most popular is an SDS-Max ¼ inch x 13 inch masonry bit with carbide tip .
Step 2: Drill the Hole
Put on safety goggles, gloves and make sure there are no bystanders in the area. Hold the drill firmly while you begin drilling slowly into the concrete surface (this will take some time). You don’t need to press hard; you just need to let the drill do its work.
Once you reach your desired depth, stop.
Step 3: Hammer Time
Insert a nail into the hole you just drilled and give it a good whack with your hammer. Remove the nail and check your bit. If there is any concrete still stuck in the drill bit, continue to step four. If not, congratulations! You’ve successfully completed this task without a hammer drill.
Step 4: Repeat
Repeat the process until you’ve reached your desired depth for your screws. Don’t forget to use your goggles and gloves when drilling again.
Step 5: Take a Break
After you’ve finished, take a break. You deserve it for successfully completing this task without having to use a hammer drill.
Tips and Warnings
While this process can be completed manually with a regular drill, you should never attempt to do so when there is someone nearby or when the concrete is wet.
Be sure to check your drill bit regularly and remove any concrete that may be stuck inside. If you don’t, the heat can build up and cause damage to your drill or even start a fire.
Drilling Concrete with Masonry Bit and Regular Drilling
You can employ this method with masonry drill bits to bore holes in stone or other masonry equipment. In order to break through the surface, hammers are used in three distinct ways by Hammers Drills. Hammers are frequently found in distinct locations.
It can quickly drill through concrete or stone due to its quick, high-speed drilling. Carbide tipped masonry bits are used in both situations. Concrete drill bits are not tough enough with tungsten carbide tips. Tungsten carbide tips on the type of masonry drill bits make them heavy-duty.
How do concrete drill bits work?
The most useful components of an excavation drill for concrete are masonry. It is typically produced of heavier-duty tungsten carbide and has a larger diameter at the tip, reducing the risk of breaks and damaged. It has a rotationally rotating drill, which also smashes out the drill bit in the concrete while digging holes.
While digging holes, drills operate at a high rate and intensity, forcing them to pierce the concrete with tremendous force and speed. A Hammer Drill is for masonry that is built the same way as brick and cement.
Do I need a special drill for concrete?
A basic drill will be capable of drilling into concrete with enough power. However, the procedure will not be efficient and long-lasting. Hammering tools are simple to create. The other factors to consider are the age of the concrete and the depth of the trench hole required.
It will be more challenging to drill a larger diameter hole by hand than it would be to drill a smaller one. The hardness of concrete rises with time, making drilling in an existing block with a drill difficult.
Carbide Core Bits
Tungsten carbide is a highly durable and flexible material. The metal frame’s carbide-tipped tools make the body more durable and flexible while keeping the resulting cutting tips hard. It makes it simpler to hit the concrete or masonry without having a hammer drill.
The drawback of utilizing a carbide cutter is that the tip of the carbide cutter often slips or cracks when struck with a bar used for heavy-duty drilling. It’s also an excellent tool for basic exercises with rotary hammers or conventional tools. This page has more information on how carbide holes are used.
Diamond Core Bits
Diamond core bits can be rolled through concrete and bar with ease. Do not use a diamond core tool with hammer since it would cause damage at cuts on it. An arbor is recommended with both tungsten carbide and diamond-core drill bits.
Use a drill that is rated at 850 Watts or greater to achieve maximum effects and the drill also needs a safety clutch. The benefits with diamond – coring is that they grind. Through concrete and bar to be used more easily. The arbor must then be mounted with either a diamond or tungsten carbide bit for a high density diamond.
While it may be possible to drill through concrete by hand, the task can be very difficult and dangerous. Especially for larger or deeper holes, a hammer drill is recommended.
To make this process more efficient and faster, you should use a Tungsten Carbide Masonry Drill Bit . It allows you to make holes in masonry such as concrete, brick and even some stones.